REPO Bot Lite - Setup, Controls, and Help

Start here for quick setup, controls, troubleshooting, and support.

Setup Video

Watch this quick 20-second setup video to get your REPO Bot Lite up and running.

Setup video placeholder
Replace this area with your embedded setup video when it is ready.
!
Power Supply Warning Use only the included 12V DC power supply. Using the wrong power supply can permanently damage the robot.

Quick Start

  • 1Place REPO Bot Lite on a flat surface.
  • 2Keep the area above the mouth clear.
  • 3Plug in the included 12V power supply.
  • 4Connect to Bluetooth on your phone, tablet, or computer.
  • 5Blue eyes mean the robot is connected.
  • 6Play audio on your connected device.

Button Controls

Buttons are labeled M, -, and +.

LED Menu

Hold M for 2 seconds to enter. Press + or - to change color. Tap M to switch to brightness adjustment, then press or hold + or - to change brightness. Hold M for 2 seconds to exit.

LED Menu video
Embed a short LED Menu walkthrough here later.

Mouth Menu

Hold + and - together for 2 seconds to enter. Press + to open the mouth and enable Mouth Hold Mode. Press - to close the mouth and return to normal audio-reactive movement.

Mouth Menu video
Embed a short Mouth Menu walkthrough here later.

Neutral Calibration

While in the Mouth Menu, press M to enter neutral calibration. The LEDs will turn amber. Press or hold + or - to adjust the mouth neutral position. Hold M for 2 seconds, or hold + and - for 2 seconds, to exit the Mouth Menu.

Neutral Calibration video
Embed a short neutral calibration walkthrough here later.

Troubleshooting and FAQ

Quick answers to the most common issues.

Make sure the power plug is fully inserted into the robot. A loose connection can cause the robot to power on and off repeatedly before starting normally. Once fully connected, the robot should power on within about 20 seconds. If it still does not light up or move after 20 seconds, contact support@1tekshop.com.

Look for REPO_BT_XXXX in your device’s Bluetooth settings. The last four characters will be different on each unit.

Make sure REPO_BT_XXXX is connected and selected as your audio output device, and that your device volume is turned up. Try pausing and replaying audio, or disconnecting and reconnecting Bluetooth. If audio works on another device but not yours, the issue is likely with that device’s audio settings. If audio does not work on multiple devices, contact support@1tekshop.com.

Check the eye color for a status warning. See Status Light Reference below.

  • Prolonged red eye animation + limp mouth - The robot is overheating and has intentionally stopped mouth movement to allow the motor to cool down. Let it cool down fully before trying again. If this happens unusually often, contact support@1tekshop.com.
  • Amber double-blink pattern - Jam detected. Remove anything blocking the mouth.
  • Magenta eyes with a repeating fade - This may indicate a position sensor issue and typically requires support.
  • Solid orange eyes - This may indicate a motor communication issue and typically requires support.

If there is no warning state shown, try restarting the robot by unplugging it and plugging it back in. If the problem continues, contact support@1tekshop.com.

Hold the M button for 2 seconds to exit. In the Mouth Menu, holding + and - for 2 seconds will also exit.

Please contact support@1tekshop.com with your order number and photos or a short video of the damage. Repair options depend on the type of damage.

Before contacting support, try restarting the robot by unplugging it and plugging it back in, then reconnect Bluetooth. If the issue continues, email support@1tekshop.com with your order number and a short video of the problem.

Status Light Reference

Use this section if the robot is powered on but not behaving as expected.

Blue eyes fading in and out twice - Bluetooth connected.
Red eyes fading in and out twice - Bluetooth disconnected.
Prolonged red eye animation + limp mouth - The robot is overheating and has intentionally stopped mouth movement to allow the motor to cool down. If this happens unusually often, contact support@1tekshop.com.
Amber double-blink pattern - Jam detected. Remove anything blocking the mouth.
Magenta eyes with a repeating fade - May indicate a position sensor issue. This typically requires support.
Solid orange eyes - May indicate a motor communication issue. This typically requires support.
If you see a hardware-related warning state that does not clear after restarting, contact support@1tekshop.com before opening the robot.